Disclaimer: As an Amazon Associate I earn from qualifying purchases. Without Any Extra Cost to You!
Last Updated on February 14, 2022 by John Robinson
When your JVC car stereo buttons suddenly stop working, it can be frustrating. You may not know what is causing the problem, or where to turn for help. In this blog post, we will explore some possible reasons why your JVC car stereo buttons are not functioning correctly and provide some solutions to get you back on the road!
5 Reasons why your JVC Car Stereo buttons are not working
Reason 1: Loose connecting ribbon Cable
For some reason, the leading cause of why JVC car stereo buttons are not working is that the connecting ribbon cable has come to lose. This is especially true for receivers that are more than 10 years old. The ribbon cable is the flat cable that connects the faceplate buttons to the main control board inside the receiver. When this cable gets lose, it is only natural that the face-plate buttons don’t work. The fact is, however, that the ribbon cable can be tightened.
To check for this problem, you first need to open the receiver face-plate by using a flat screwdriver. This will need to be done cautiously so as not to damage the faceplate or scratch it up. That being said, you should see two or three flat ribbon cables at the back. You will need to tighten each one of these cables by turning them carefully. If you notice that one of the cables is not connected to anything at all, you need to fix it before the faceplate buttons will work again.
This is a quick and easy fix that only takes a few minutes to complete.
Reason 2: single stuck button
If you have a single stuck button on the JVC faceplate, this can cause other buttons to stop working as well. What happens in this situation is that when you press one button, the electrical charge sends a message to all of the buttons. Since you have only one button that is stuck, the rest of the buttons will think that you are pressing them simultaneously. In this way, they don’t function correctly and all the buttons stop working.
To fix this problem, you need to open the faceplate and find the offending button that is stuck. You will need to press the tip of a small flat screwdriver into the button mechanism to free it. Your JVC car stereo buttons should work properly once again after this.
Reason 3: Wiring is damaged
Another common reason why your JVC car stereo buttons are not working properly is that the wiring between the faceplate and the main control board has been damaged. This can happen over time if you are using the buttons too heavily or frequently.
Reason 4: Buttons are worn out
The buttons of your JVC car stereo can already be problematic if you have not been using it for a very long time. If you see that the buttons of your stereo are all worn out, then this can already be an indication that you need to replace them. This is a good option for you so this will not be a problem anymore.
Buttons generally wear out when they are constantly pressed and used. This is the reason why you will see that buttons become worn out and this can be a problem for you. It may become a problem for you especially if some of the buttons are not functioning while you are using your stereo.
Reason 5: Dust
There are also times when the buttons will not work even if they are not worn out. This may be because you do not use your stereo often or because of dust. Dust can also cause the buttons to be unresponsive. If you are experiencing this, then you should do something about it right away.
You can fix this problem by cleaning the buttons and making sure that there is no dirt or dust on them. It may be a problem if you still encounter this issue after cleaning it. If this is the case, then you have no choice but to replace it.
Quick Fix – Checking touch learning settings
You can try checking touch learning settings on your JVC car stereo. For this follow the following guidelines given below.
Step 1: Go to Home screen and find car setting
Step2: Now click on touch learning
Step 3: Now click each function and then its button to set it.
Step 4: That’s it now you can use your stereo buttons.
Howdy! I’m John Robinson from Levittown, New York. I am a mechanical engineer for 15 years and already had an established car repair company. I developed a personal relationship with cars since I was a kid. I always love the sounds and smell emitted by a car or truck and even at construction machinery. Since then I have been married but my love for cars only grew.